Faculty Publications

Dr. K. P. Arulshri

International Journals

K. P. Arulshri,  “A study on kerf characteristics of hybrid aluminium 7075 metal matrix composites machined using abrasive water jet machining technology”  Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, SAGE Publications, June 2016.

Jeyaraj.S, K.P.Arulshri, S.Sivasankaran, "Investigations on effect of process parameters of electrodeposited Ni-Al 2 O 3 composite coating using orthogonal array approach and mathematical modeling", Archives of Civil and Mechanical Engineering 16 (1), 168-177, 2016,doi:10.1016/j.acme.2015.07.04

Jeyaraj.S, KP Arulshri, PS Sivasakthivel, S Dhasarathy, R Saravanan, "Experimental Investigations and Effect Studies on Electrodeposited Nickel-Slag Powder Composite Coatings" Indian Journal of Science and Technology, vol 8 (22) ,(2015), ISSN: 0974-6846

S Jeyaraj, R Saravanan, KP Arulshri, "Effect studies on Electrodeposited Ni-Al₂O₃composites by conventional and sediment type co-deposition methods using Taguchi approach", International Journal of Engineering and Technical Research (IJETR), Volume-3, Issue-3,March 2015,ISSN: 2321-0869

S Jeyaraj, V Sudhambarish, VS Karthik, KP Arulshri, "Effects of Process parameters on Microhardness of Electrodeopsited Ni-Fly ash-SiC Composite Coatings using Taguchi approach", International Journal of Engineering and Technical Research (IJETR), Volume-3, Issue-3,March 2015,ISSN: 2321-0869

S Jeyaraj, G Muralidharan, KP Arulshri, R Saravanan, "Influence of process parameters on Electrodeposited Nickel thin film coating using Taguchi approach", International Journal of Engineering and Technical Research (IJETR), Volume-3, Issue-4, 2015,ISSN: 2321-0869

S Jeyaraj, KP Arulshri, KP Harshavardhan, PS Sivasakthivel, "Optimization of Flame Hardening Process Parameters Using L9 Orthogonal Array of Taguchi Approach", International Journal of Engineering and Applied Sciences (IJEAS), Volume-2, Issue-3, 2015,ISSN: 2394-3661

MM Madhan Gopal, PS Vishnu, S Jeyaraj, KP Arulshri, "Influence of process parameters on Electrodeposited Ni-Al₂O₃ composites by conventional and sediment type of co-deposition by Grey Scale Analysis", International Journal of Engineering and Applied Sciences (IJEAS), Volume-2, Issue-8, 2015,ISSN: 2394-3661

Selvakumar, S., K.P. Arulshri, "Machining fixture layout optimisation using genetic algorithm and artificial neural network." International Journal of Manufacturing Research 8(2): 171-195, (2013), ISSN: 1750-0591

Sethusundaram P.P., K.P.Arulshri, K.Mylsamy,(2013). "Biodiesel Blend, Fuel Properties and its Emission Characteristics Sterculia Oil in Diesel Engine", International Review of Mechanical Engineering (IREME) 7 (5): 925-929

Boopathi.M.M, KP Arulshri, P Shanmughasundaram, (2013), "Analysis of Burr Formation and Surface Roughness in Step Drilling of AA 2024–SiC-Fly Ash Hybrid Composites", International Review of Mechanical Engineering (IREME) 7 (7), 1347-1354.

Boopathi, M. M., K.P. Arulshri, (2013). "Evaluation of Mechanical Properties of Aluminium Alloy 2024 Reinforced With Silicon Carbide And Fly Ash Hybrid Metal Matrix Composites" American Journal of Applied Sciences 10(3).

Sethusundaram.P.P, P Govindasamy, KP Arulshri, (2012), "Sterculia Oil on Single Cylinder Four Stroke Diesel Engine with Water Cooled Exhaust Gas Recirculation", European Journal of Scientific Research 91 (1), 91-99

Jeyaraj, S. And K.P. Arulshri (2012). "Characterization of Electrodeposited Nickel-Al2O3 Composite Coatings by Experimental Method and Neural Networks. "Journal of Applied Sciences 12: 911-919.

Padmanaban, K., K.P. Arulshri, (2009). "Machining Fixture Layout Design Using Ant Colony Algorithm Based Continuous Optimization Method. "The International Journal of Advanced Manufacturing Technology 45(9-10): 922-934.

Padmanaban, K. P., K. P. Arulshri, (2009). "Machining Fixture Layout Design Using Ant Colony Algorithm Based Continuous Optimization Method. "The International Journal of Advanced Manufacturing Technology 45(9-10): 922-934.

Sasikumar, K., S. Selvakumar, K. P. Arulshri (2011). "An Analysis Of The Effect Of Constraining Layer Modulus On The Vibration Control Of Beams Treated With Pcld." European Journal Of Scientific Research 66(3): 377-391.

Selvakumar, S., K.P. Arulshri, (2010). "Clamping Force Optimization For Minimum Deformation Of Workpiece By Dynamic Analysis Of Workpiece -Fixture System." World Applied Sciences Journal 11(7): 840-846.

Selvakumar, S., K.P. Arulshri, (2012). "Mathematical Approach For Optimal Machining Fixture Layout And Clamping Forces." Australian Journal Of Mechanical Engineering 10(1): 17.

Selvakumar, S., K.P. Arulshri, (2013). "Design and Optimization Of Machining Fixture Layout Using Ann And Doe." The International Journal Of Advanced Manufacturing Technology 65(9-12): 1573-1586.

Selvakumar, S., K.P. Arulshri, (2013). "Machining fixture layout optimisation using genetic algorithm and artificial neural network." International Journal of Manufacturing Research 8(2): 171-195.

KSK Sasikumar, K.P. Arulshri and, S Selvakumar " An analysis of the effect of constraining layer modulus on the vibration control of beams treated with PCLD, European Journal of Scientific Research, 2011, Vol. 66,
No.3, 377-391.

KSK Sasikumar, K.P. Arulshri and S Selvakumar, "Study of the effect of composite constrained layers in vibration damping of plates", International Journal of Applied Mechanics and Engineering, 2014, Vol.19, No.1, 203-209.

KSK Sasikumar, K.P. Arulshri, S. Selvakumar, and NS Nandakumar, "Numerical and experimental study of the Effect of Constraining Layer in controlling the vibration of beams attached with PCLD",Bulletin of Applied Mechanics ,2011,Vol.7,No.25.

KSK Sasikumar, K.P. Arulshri, and S Selvakumar, "Some Studies on the Effect of Constraining Layer in the Vibration Control of Beams using PCLD".International Journal of Applied Engineering Research,2010,Vol. 5,No.15.

Dr. K. L. Senthil Kumar

International Journals


Saravana kumar.M, K.L.Senthil kumar, "An Investigation of multi walled carbon nanotubes based nano cutting fluids in turning of martensitic stainless steel by using taguchi and anova analysis", IOSR Journal Of Mechanical and Civil Engineering, pp08-15, 2014, e-ISSN:2278-1684

Rameshkumar T, Rajendran, I. and Senthil Kumar, K. L., "Mass Loss Prediction of TiN based Plain Bearing Alloy using Artificial Neural Network", Procedings of the Second International Conference on Advances in Materials Processing and Characterization (AMPC 2013), Vol. II, pp: 108-

Senthil Kumar, K. L. and Sivasubramanian, R, "Modeling of metal removal rate inmachining of aluminium matrix compositeusing artificial neural network", Journal of Composite Materials, October 2011, vol. 45 no. 22 2309-2316, DOI: 10.1177/0021998311401083.

Senthil Kumar, K. L. and Sivasubramanian, R. "Optimization of Parameters in Electrochemical Machining of Composite Material using Genetic Algorithm", Proc. of Int. Confer. on Adv. Manuf. (ICAM 2011), pp: 30-33, TATI University College, Terengganu, Malaysia, 23-24 May 2011.

Senthil Kumar, K. L., Sivasubramanian, R and Kalaiselvan, K. "Selection ofoptimum parameters in non conventional machining of metal matrix composite", Portugaliae Electrochimica Acta, Vol. 27, No. 4, pp.: 477-486, 2009, DOI:10.4152/pea.200904477.

National Journals

Senthil Kumar, K. L. and Sivasubramanian, R. "Optimization of machining process in machining particulate reinforced aluminium matrix composite", Manufacturing Technology Today, Vol. 8, No. 9, pp: 21-26, 2009.

Senthil Kumar, K. L. and Sivasubramanian, R. "Optimization of machining process in machining particulate reinforced aluminium matrix composite", Manufacturing Technology Today, Vol. 8, No. 9, pp: 21-26, 2009.

National Conference

K L Senthil Kumar, T Rameshkumar and S Boopathy, "Optimization of Machining Parameters using Taguchi Technique", in the 6th National Conference on OPTEST 2011, during 15-16 April 2011, at BIT, Sathy.

T Rameshkumar and K L Senthil Kumar, "A Study on Tribological Properties of Aluminium Composite Materials", in the 6th National Conference on OPTEST 2011, during 15-16 April 2011, at BIT, Sathy.

B. N. Pranesh, M Venkatesan, S Vignesh and K L Senthil Kumar, "Optimization of Parameters for MMC preparation using Stir Casting Process" 7th National Conference on OPTEST 2012, during 20-21 April 2012, at BIT, Sathy.

R S Ragavendiran, K Kathirvel, K. Sathish Kumar, K L Senthil Kumar and T Rameshkumar, "Optimization of Dielectric Fluid Parameters in Machining of MMC using EDM", 7th National Conference on OPTEST 2012, during 20-21 April 2012, at BIT, Sathy.

K Kathirvel, T Rameshkumar, R S Ragavendiran and K L Senthil Kumar, "Wear Prediction of Newly Developed Aluminium based Alloys using Optimization Techniques", 7th National Conference on OPTEST 2012, during 20-21 April 2012, at BIT, Sathy.

Dr. S. Ramesh

International Journals

Ramesh, S, Natarajan, N, Krishnaraj, V, "Experimental investigation of Al6061/SiCp/B4Cp hybrid MMCs in wire electrical discharge machine", NISCAIR-CSIR,Vol. 21, 409-417, 2014,ISSN: 0971-4588.

Ramesh S, Natarajan N, Krishnaraj V & Gokulakannan, G, 'Determination of cutting operation number for multipass cutting in WEDM of composite materials', International Journal of Applied Engineering Research, vol. 9, no. 24, pp. 27041-27051,2014.

Ramesh S, Natarajan N & Krishnaraj V, 'Effect of multipass cutting on surface roughness in wire electrical discharge machining of metal matrix composites', Carbon - Science and Technology, vol. 6, no. 3, pp. 14-21, 2014.

Ramesh, S & Natarajan, N, 'Optimization of Wire Electrical Discharge Machining of Hybrid Metal Matrix Composite Material', International Review of Mechanical Engineering, vol. 7, no.1, pp. 110-114, 2013.

S.Ramesh, N.Natarajan, V.Krishnaraj and K.Sathish Kumar "Investigation on the effect of multi wall carbon nano tubes in Wire Electrical Discharge Machining of hybrid Metal Matrix Composites" Applied Mechanics and Materials Vols. 592-594 (2014) pp 456-460, 2014. Impact factor - 0.125.

S Ramesh and Dr N Natarajan, "Optimization of Wire Electrical Discharge Machining of Hybrid Metal Matrix Composite Material" International Review of Mechanical Engineering, Volume 7 (No.1) (2013), pp 110-114. Impact factor - 0.638.

Sateesh Kumar Reddy Kuricheti, Ramesh S, "Parametric optimization of wire electrical Discharge machining of composite material" International Journal of Advanced Research in Computer Engineering & Technology, Vol. 1 (No.3), 2012.

National Conference

K.Sathishkumar, S. Ramesh, N.Natarajan, V. Krishnaraj, Experimental Investigation of Machining characteristics of Hybrid Composite in Wire Electrical Discharge Machining, in the proceedings of Optimization Techniques in Engineering Sciences and Technologies (OPTEST -2014), 4th 5th April 2014.

D.Prabhu, S.Ramesh, Dr N.Natarajan and Dr.V.Krishnaraj, "Prediction of Material Removal Rate and Surface Roughness of Composite Material in WEDM Using ANN" in the proceedings of Optimization Techniques in Engineering Sciences and Technologies (OPTEST - 2013), 19th 20th April 2013.

S.Mehanathan, S.Ramesh, Dr N.Natarajan and Dr.V.Krishnaraj, "Optimization of machining parameters of composite material for WEDM" in the proceedings of Optimization Techniques in Engineering Sciences and Technologies (OPTEST - 2013), 19th, 20th April 2013.

N.Santhosh and S.Ramesh, "Design Of an Integrated Gripper for Robotic Pick and Place" in the proceedings of Optimization Techniques in Engineering Sciences and Technologies (OPTEST - 2013), 19th, 20th April 2013.

K.Satheesh Kumar Reddy, S.Ramesh, Dr.N.Natarajan, "Parameteric optimization of Wire Electrical Discharge Machining of Composite Materials" in the proceedings of Optimization Techniques in Engineering Sciences and Technologies (OPTEST -2012), 20, 21 April 2012.

Internaational Conference

S Ramesh and Dr N Natarajan, "Optimization of machining parameters for wire electrical discharge machining", proceedings of Innovations in Engineering and Technology for Sustainable Development (IETSD 2012) 3-5 September 2012 Bannari Amman Institute of Technology, Sathyamangalam, ISBN 978-81-920-460-3-7, Vol.1, pp ME-112.

Mr. M. Sengottuvelan

National Conference

M. Sengottuvelan , “Identification and Analysis of Cold Metal Defect in Ferrous Casting using TRIZ Integrated Six Sigma Approach” Asian Journal of Research in Social Sciences and Hummanities  Vol.6, Issue 6, Special Issue Jenu 2016, pp259-266

Omprakas.M.A and Sengottuvelan M, "Investigation and Analysis of cold metal defection in Grey Cast Iron by Six-sigma Method using Minitab", Proceedings of National Conference on Advances in Civil and Mechanical Engineering (ACME-2014) on 25th March 2014, Sengunthar Engineering College, Erode.

Sengottuvelan M, Dr. Sivakumar K, Nandagopal M, Omprakas M.A, " Identification and Analysis of cold metal defect in Ferrous casting using Six-sigma by Taguchi Method in Minitab", proceedings of OPTEST 2014: 04-05 April 2014, Bannari Amman Institute of Technology, Sathyamangalam.

Nandagopal M, , Dr. Sivakumar K, Sengottuvelan M, Kamalakannan.A, " Process parameters optimization to reduce the sand casting defects", proceedings of OPTEST 2014: 04-05 April 2014, Bannari Amman Institute of Technology, Sathyamangalam.

M.Natrayan, M. Sengottuvelan, V.C.Uvaraja, "Comparison of two unique reinforcement materials with Al-6061 alloy produced by stir casting method", proceedings of OPTEST 13: 19-20 April 2013, Bannari Amman Institute of Technology, Sathyamangalam.

G.Gnanasekar, M. Sengottuvelan, V.C.Uvaraja, "Mechanical and Tribological properties of Al-606 metal, Reinforcement of SIC and Al2O3 by using stir casting method", proceedings of OPTEST 13: 19-20 April 2013, Bannari Amman Institute of Technology, Sathyamangalam.

M.Sengottuvelan, S.Chandika, C.Jagadheesan, Dr.R.Asokan," Study on Piezo Actuated Micro pumps" in the National Conference on Recent Advances in Control, Communication & Electrical Engineering, during March 31 and April 1,2010, Sethu Institute of Technology.

Ms. K. Poomani

International Journals

K. Poomani, “Enhanced Proportional Integral Derivative control strategy for Magnetic Ball Levitation System” International Journal of Hybrid Information Technology Vol.9 No.6(2016), pp.295-302.

K. Poomani, R.Rameswari, “Enhanced Pid Control Strategy Application To Spherical Tank System”, International Journal for Research in Applied Science & Engineering Technology (IJRASET), Volume 3, Issue III, PP:138-141, March 2015, ISSN: 2321-9653.

International Conference

K. Poomani, S. Sathiyavathi and K. Krishnamurthy, "PID Tuning for Magnetic Ball Suspension System" in the 5th International Conference on Science, Engineering and Technology 2012, during 8-9 Nov, at VIT, Vellore.

National Conference

K. Poomani, "Mixed Rectifier For Dynamic Load Applications" in the 1st National Conference on Electrical Systems-NCES'12, during 21-22 March 2012, at RVS College of Engg & Tech, Coimbatore.

K. Poomani, S. Sathiyavathi and K. Krishnamurthy, "Hybrid Current Cycle ILC Strategy for Magnetic Ball Suspension System" in the National Conference on Innovations in Mechanical, Mechatronics and Building Sciences, NCIMMBS-13, during 25-26, April 2013, at Kongu Engineering College, Perundurai.

Mr. S. K. Dhinesh

International Journals

S.Suresh, J.S.Venkatesan, S.K.Dhinesh "Proposed Design for Automobile Door Clearance Mechanism" International Journal of Advanced Information Science and Technology, Vol.25, Issue.25, May 2014.

National Conference

S. Manikandan, "Effect of Substrate in Microstrip Fed double Sided Rounded Bow-Tie Antenna" in the National Conference on Recent Trends and Research issues in Antennas, during 09-10 Feb 2010, at Dr.Sivanthi Aditanar College of Engg, Tiruchendur.

Mr. S. Manikandan

International Journals

Meenakshipriya B, Manikandan S, “Wiener model based CDM PI controller for pH neutralisation process”, International journal of modeling Identification and control, Vol 24, No. 2, 2015, DOI: 10.1504/IJMIC.2015.071889.

National Conference

S.K. Dhinesh, R. Parameshwaran, S. Praveen Kumar "Improving the Cooling Performance of Automotive Radiators by applying Electric field in various Coolants" in the National Conference on Innovations in Mechanical, Mechatronics and Building Sciences, NCIMMBS-14, during 25-26 April 2013, at Kongu Engineering College, Perundurai.

International Conference

S. Manikandan, "Established Control Techniques For pH Neutralization Process" in the International Conference on Synchronizing Management Thoeries and Business Practices: Challenge Ahead, held during 27-29 July 2012 at Annamalai University, Chidambaram.


B. Meenakshipriya and S. Manikandan, "Design and Implemantation of Wiener Model Based CDM-PI Controller in pH " Neutralization System" in the International Simulation Conference of India 2013, held during 21-23 Feb 2013 at IITM, Chennai.

Mr. S. Javid Ahamed

International Journals

S. Javid Ahamed, P. Balakrishnan and P. Archana, "Autonomous Agrobot for Rice Cultivation" International Journal on Recent Researches In Science, Engineering And Technology (JRRSET), Volume 2, Issue 2, ISSN(print) 2347-6729 &ISSN (online) 2348-3105.

International Conference

P. Balakrishnan, P. Archana and S. Javid Ahamed, "A Novel Approach for Random Image Steganography" Proceedings on International Conference on Advances in Engineering, Technology and Management (ICAETM), 2014.

National Conference

S. Javid Ahamed, "Autonomous Agrobot for Rice Cultivation" Proceedings on National Conference on Recent Trends in Mechanical Engineering (NCRTME' 13), Trichy, Tamil Nadu, India, 2013.

Mr. A. Prakash

International Conference

A.Prakash and S.K.Thangarasu, "Analysis of Tool wear using Cutting Force and Vibration Technique" in the International Simulation Conference of India 2013, held during 21-23 Feb 2013 at IITM, Chennai.

Mr. C. Dinesh

International Journals

C. Dinesh, V. V. Manikanta, H. S. Rohini and K. R. Prabhu,"Real Time Level Control of Conical Tank and Comparison of Fuzzy and Classical Pid Controller", Indian Journal of Science and Technology,Vol 8(S2), 40–44, January 2015,ISSN (Print) : 0974-6846.

Mr. C. Dinesh, Mr. R. Sivabalakrishnan “Optimized terrain Robot for Liberating the human in catastrophe” International Journal for Research in applied science and Engineering Technology, Volume 4, Issued III, Page No. 539 to 544, March 2016 ISSN-2321-9653.

Mr. R. Sivabalakrishnan

International Journals

Sivabalakrishnan R, "Trusted Routing with an Efficient Certificate Revocation for Mobile Ad Hoc Network",  IJISET - International Journal of Innovative Science, Engineering & Technology, Vol. 2 Issue 3, pg. 755-762, March 2015. , ISSN 2348 – 7968

Sivabalakrishnan R, “Study of Knocking Effect in Compression Ignition Engine with Hydrogen as a Secondary Fuel”, Hindawi Publishing Corporation, Chinese Journal of Engineering, Volume 2014, DOI: 10.1155/2014/102390.

Mr. R. Sivabalakrishnan Mr. C. Dinesh, “Optimized terrain Robot for Liberating the human in catastrophe” International Journal for Research in applied science and Engineering Technology, Volume 4, Issued III, Page No. 539 to 544, March 2016 ISSN-2321-9653.

International Conference

Mr. R. Sivabalakrishnan, “Microcontroller based autonomous Robot system for rescuing alive human” International conference on Mechanical and Building Science, Pg. No. 272-275” March 2016.

National Conference

Mr. R. Sivabalakrishnan and Ms. K. Poomani, “Automatic Headlight change over safety system” in Intelligent Automation in science Engineering and Technology, Pg. No. 149-151, March 2016.

Mr. F. Valliyullah Khan

International Journals

F Valiyullah khan,  Narayana siva Teja,A.L.Aaqib Parvez, Rashmi Rajan Das, "Low Cost Smart Home Design", Indian Journal of Science Technology, 2015,ISSN: 0974-6846.

F Valiyullah khan,  Narayana siva Teja, Rashmi Rajan Das, "voice controlled robot", 2013.

Mr. S. Vignesh

International Journals

Vignesh, “Comparison of the Optimized Process Parameters of Double-Sided Friction Stir Welded Aluminium Alloy Joints Using Statistical and Evolutionary Techniques” Applied Mechanics and Materials, ISSN: 1662-7482, Vol. 852, pp 317-323 (Impact Factor - 0.16), September 2016.

Vignesh S., “Development of mathematical models and Optimization of the laser welding process parameters using Response Surface Methodology”  ARPN Journal of Engineering and Applied Sciences (Scopus Indexed) , Vol. 11, Page. No. 12, August 2016.

Mr. S. Aravinth

National Journals

Araninth S, “Vibration Based Brake Fault Diagnosis Using Voting Feature Interval and Decision Tree with Histogram Features” Indian Journal of Science and Technology, Vol 9(33), 1-5.